Chemical Compositions of AISI (ASTM/ASME) and UNS Martensitic And Precipitation Hardening Stainless Steel Grades
Chemical composition of AISI (ASTM / ASME) and UNS martensitic and precipitation-hardening stainless steel grade
Most ASTM and ASME standards list the steel grades by their UNS, (Unified Numbering system), numbers but also make reference,
where appropriate to the more general AISI, (American Iron and Steel Institute), grade designations. These grade numbering systems
are widely used in the USA, where they originated and are recognised by most stainless steel specifiers and users. In Japan the
AISI grade number is preceded by SUS, e.g. SUS 630. The chemical compositions of stainless steel grades covered in this article
include AISI / common grade names 410, 414, 416, 416Se, 420, 420F, 420FSe, 429, 431, 440A, 440B, 440C, 440F, 440FSe, 630, 631,
632, 633, 634, 635, PH13-8Mo, 15-5PH, 15-7PH, 17-4PH, 17-7PH, A286, Trim Rite, XM-6, (416 Plus X), XM-13, XM-12, XM-16,
Custom 455, XM-25, Custom 450, XM-30, SAE grades, 51410, 51414, 51416, 51416Se, 51420, 51420F, 51420FSe, 51429, 51431,
51440A, 51440B, 51440C, 51440F, 51440FSe, and UNS grades S13800, S15500, S15700, S17400, S17600, S17700, S35000, S35500,
S41000, S41040, S41400, S41500, S41600, S41610, S41623, S42000, S42010, S42020, S42023, S42900, S43100, S44002, S44003,
S44004, S44020, S44023, S45000, S45500, S45503, S46500, S66286.
CHEMICAL COMPOSITIONS OF AISI (ASTM/ASME) AND UNS MARTENSITIC AND PRECIPITATION HARDENING STAINLESS STEEL GRADES
Introduction – AISI, ASTM, ASME and UNS
Most ASTM and ASME standards list the steel grades by their UNS, (Unified Numbering system), numbers, but also make reference,
where appropriate to the more general AISI, (American Iron and Steel Institute), grade designations. These grade numbering systems
are widely used in the USA, where they originated, and are recognised by most stainless steel specifiers and users.
The American Iron and Steel Institute, (AISI), developed designations such as 420, 440 etc. and published compositions for these in
their ‘Steel Products Manual’, (1974).
These are NOT specifications, but steel grade composition ranges only.
These grades were used by the American Society Testing and Materials, (ASTM), to identify grades in a wide range of standards they
published for stainless products, such as sheets and plates, (ASTM A240), bars, (ASTM A276) and tubes, (ASTM A269).
The compositions of the AISI grades were made more specific with the introduction of the ‘Unified Numbering System’, jointly established
by ASTM and SAE, (Society of Automotive Engineers).
This five digit number, preceded by the letter ‘S’ for most stainless steels, identified the specific variant of the grade
e.g. 420 being UNS S42000, 630 or 17/4PH being UNS S17400
American Society of Mechanical Engineers, (ASME), publish design codes and standards for pressure applications. ASME standards
are generally based on the appropriate ASTM standards, but the standard numbers are preceded with the letters ‘SA’, rather than
just the ‘A’ of the ASTM standards.
Where UNS grade numbers are used, these are universal, regardless of the product type or the standard in which they appear.
The AISI designations have been adopted in Japan. The AISI number is preceded with the letters SUS, e.g. SUS 630.
The Japanese have developed variants on some grades for certain product forms, e.g. SUS 304J1 for sheet products.
The composition ranges should always be checked in the appropriate standard.
Composition tables
The tables in this article use the UNS number as their key, but also show the related AISI and SAE numbers. Where appropriate,
common names for the steels are also shown.
As an alternative to scanning down the list try the ‘find’ facility on your keyboard, using the ‘Ctrl’ and ‘F’ keys together.
Type in the term you are looking for in the dialog box that then appears.
The data given is not intended to replace that shown in individual standards to which reference should always be made.
Martensitic and precipitation hardening grades
Designation Chemical composition % by mass max unless stated
UNS No SAE No AISI No / Common Name C Si Mn P S Cr Mo Ni Others
S13800 – XM-13 PH13-8Mo 0.05 0.10 0.20 0.010 0.008 12.25/13.25 2.00/2.50 7.50/8.50 N 0.01; Al 0.90/1.35
S15500 – XM-12 15-5PH 0.07 1.00 1.00 0.040 0.030 14.0/15.5 – 3.50/5.50 Cu 2.5/4.5; Nb+Ta 0.15/0.45
S15700 – 632 15-7PH 0.09 1.00 1.00 0.040 0.030 14.00/16.00 2.00/3.00 6.50/7.75 Al 0.75/1.50
S17400 – 630 17-4PH 0.07 1.00 1.00 0.040 0.030 15.00/17.50 – 3.00/5.00 Cu 3.00/5.00; Nb+Ta 0.15/0.45
S17600 – 635 0.08 1.00 1.00 0.040 0.030 16.00/17.50 – 6.00/7.50 Al 0.40; Ti 0.40/1.20
S17700 – 631 17-7PH 0.09 1.00 1.00 0.040 0.030 16.00/18.00 – 6.50/7.75 Al 0.75/1.50
S35000 – 633 0.07/0.11 0.50 0.50/1.25 0.040 0.030 16.00/17.00 2.50/3.25 4.00/5.00 N 0.07/0.13
S35500 – 634 0.10/0.15 0.50 0.50/1.25 0.040 0.030 15.00/16.00 2.50/3.25 4.00/5.00 N 0.07/0.13
S41000 51410 410 0.08/0.15 1.00 1.00 0.040 0.030 11.5/13.5 – 0.75 –
S41040 – XM-30 0.18 1.00 1.00 0.040 0.030 11.0/13.0 – – Nb 0.05/0.30
S41400 51414 414 0.15 1.00 1.00 0.040 0.030 11.5/13.5 – 1.25/2.50 –
S41500 – F6NM 0.05 0.60 0.50/1.00 0.030 0.030 11.5/14.0 0.50/1.00 3.5/5.5 –
S41600 51416 416 0.15 1.00 1.25 0.060 0.15 min 12.0/14.0 – – –
S41610 – XM-6 (416 Plus X) 0.15 1.00 1.50/2.50 0.06 0.15 min 12.0/14.0 – – –
S41623 51416Se 416Se 0.15 1.00 1.25 0.060 0.060 12.0/14.0 – – Se 0.15 min
S42000 51420 420 0.15 min 1.00 1.00 0.040 0.030 12.0/14.0 – – –
S42010 – Trim Rite 0.15/0.30 1.00 1.00 0.040 0.030 13.5/15.00 0.40/0.85 0.35/0.85 –
S42020 51420F 420F 0.30/0.40 1.00 1.25 0.060 0.15 min 12.0/14.0 – 0.50 Cu 0.60
S42023 51420FSe 420FSe 0.20/0.40 1.00 1.25 0.060 0.060 12.0/14.0 – – Se 0.15 min Cu 0.60
S42900 51429 429 0.12 1.00 1.00 0.040 0.030 14.0/16.0 – – –
S43100 51431 431 0.20 1.00 1.00 0.040 0.030 15.0/17.0 – 1.25/2.50 –
S44002 51440A 440A 0.60/0.75 1.00 1.00 0.040 0.030 16.0/18.0 0.75 – –
S44003 51440B 440B 0.75/0.95 1.00 1.00 0.040 0.030 16.0/18.0 0,75 – –
S44004 51440C 440C 0.95/1.20 1.00 1.00 0.040 0.030 16.0/18.0 0.75 – –
S44020 51440F 440F 0.95/1.20 1.00 1.25 0.060 0.15 min 16.0/18.0 0.75 0.50 Cu 0.60
S44023 51440FSe 440FSe 0.95/1.20 1.00 1.25 0.060 0.060 16.0/18.0 – – Se 0.15 min Cu 0.60
S45000 – XM-25 Custom 450 0.05 1.00 1.00 0.030 0.030 14.00/16.00 0.50/1.00 5.00/7.00 Cu 1.25/1.75; Nb 8xC min
S45500 – XM-16 Custom 455 0.05 0.50 0.50 0.040 0.030 11.00/12.50 0.50 7.50/9.50 Cu 1.50/2.50; Nb 0.10/0.50 Ti 0.90/1.40
S45503 – – 0.010 0.20 0.50 0.010 0.010 11.00/12.50 0.50 7.50/9.50 Cu 1.50/2.50; Ti 1.00/1.35 Nb 0.10/0.50
S46500 – – 0.02 0.25 0.25 0.015 0.010 11.00/12.50 0.75/1.25 10.75/11.25 Ti 1.50/1.80 N 0.01
S66286 – A286 0.08 1.00 2.00 0.040 0.030 13.50/16.00 1.00/1.50 24.0/27.0 Al 0.35; B 0.0010/0.010; Ti 1.90/2.35; V 0.10/0.50 W 1.90/2.35
Inspection & Approval Certificates : C/W Certificate (Calibration Works Certificate) EN-10204 3.1 / DIN-50049 3.1 / ISO-10474 3.1 Mill Test Certificate,
Material Test Certificate, NACE-HIC TM-0284 / NACE-MR-0103 / NACE-MR-0175 / ISO-15166, BS EN-9001, BS EN-9100, AS-9100, AS-9100D,
IATF-16949, NADCAP Certified, ITAR Compliant, CE-Marked, CE-Marking, European Pressure Equipment Directive PED-2014/68/EU, AD-2000-WO,
ASME Boiler & Pressure Vessel Code Section-II Part A Edition 2021, API-6A (American Petroleum Institute), with EN-10204 3.2 Certificate
Duly Certified & Approved by IBR (Indian Boiler Regulations), IACS Class, LR Class (Lloyd’s Register), GL (Germanischer Lloyd), BV (Bureau Veritas),
DNV (Det Norske Veritas), ABS Class (American Bureau of Shipping), SGS, TUV, RINA, IR Class (Indian Register of Shipping), DGAQA Approved,
NORSOK Approved Standard M-630, M-650 Rev.3, DFAR/DFARS Compliant, NADCAP Certified For Ministry of Defence, DRDO, DGQA Approved,
Indian Ordnance Factory, Heavy Vehicle Factory, Bharat Electronics Limited (BEL), Hindustan Aeronautics Limited (HAL), Bharat Forge Limited,
Mishra Dhatu Nigam Limited (MIDHANI), Bharat Dynamics Limited (BDL), Indian Navy (Naval Dockyard), Mazagon Dock Shipbuilders Limited (MDL),
Bharat Heavy Electricals Limited (BHEL), National Thermal Power Corporation Limited (NTPC), Aerospace, Aviation, Electric Vehicles, Armour Vehicle,
Armor Vehicle, Automotive, Automobile, Railways, Medical Equipments, Military Missiles, Energy, Power Sector, Electronics, Power Generation,
Oil & Gas, Petroleum, Natural Gas, Wind Mill, Turbine, Engine, Boilers
Make And Origin : India, Japan, Korea, Russia, China, Europe, Germany, Spain, Italy, Belgium, France, Sweden, Switzerland, Austria, U.K, America, USA
Make And Origin : Indian, Japanese, Korean, Russian, Chinese, European, Swedish, UK, American, United Kingdom, U.S.A
Top Leading Steel Maker Manufacture In The World
Shandong Iron and Steel Group (China)
PAO Severstal (Russia)
Thyssenkrupp Ag (Germany)
Voestalpine AG (Austria)
CITIC Pacific Special Steel Holdings (China)
SSAB AB (Sweden)
Hebei Puyong Iron and Steel Group Co., Ltd. (China)
Tata Steel (India)
China Steel Corporation (China)
JFE Steel Corporation (Japan)
Nippon Steel Corporation (Japan)
Daido Steel (Japan)
HBIS Group (China)
Baosteel Group Corporation (China)
Gerdau S.A. (Brazil)
Metinvest Holding, LLC (Ukraine)
Nucor Corporation (U.S.)
Hyundai Steel Company (South Korea)
Novolipetsk Steel (NLMK) (Russia)
JSW Steel (India)
United States Steel Corporation (U.S.)
Posco Iron And Steel Group (South Korea)
Hyundai Steel (South Korea)
ArcelorMittal S.A. (Luxembourg)
Steel Authority of India SAIL (India)
Jindal Steel And Power (India)
If you have any requirement of above items, please feel free to contact us
Regards,
CONTACT PERSON :
MUKESH SHAH
Director
Mobile No. 0091 – 9820292499
Email – marketing@rolexmetals.com
ROLEX METAL DISTRIBUTORS
57-A Khatargalli
Thakurdwar
Mumbai – 400002 India
0091-22-23858802
0091-22-23823963
0091-22-23898724
marketing@rolexmetals.com
www.rolexmetals.com
CHAIRMAN – chairman@rolexmetals.com
MANAGING DIRECTOR – managingdirector@rolexmetals.com
TECHNICAL DIRECTOR – technicaldirector@rolexmetals.com
SALES DIRECTOR – salesdirector@rolexmetals.com
COMMERCIAL DIRECTOR – commercialdirector@rolexmetals.com
COMMERCIAL MANAGER – commercial@rolexmetals.com
GENERAL MANAGER – generalmanager@rolexmetals.com
SALES MANAGER – salesmanager@rolexmetals.com
PURCHASE MANAGER – purchasemanager@rolexmetals.com
TECHNICAL MANAGER – technical@rolexmetals.com
WORKS MANAGER – worksmanager@rolexmetals.com
STORES MANAGER – stores@rolexmetals.com
WAREHOUSE MANAGER – warehouse@rolexmetals.com
SALES DOMESTIC – salesdomestic@rolexmetals.com
SALES INTERNATIONAL – salesinternational@rolexmetals.com
SALES GENERAL – sales@rolexmetals.com
PURCHASE GENERAL – purchase@rolexmetals.com
FINANCE MANAGER – finance@rolexmetals.com
ACCOUNTS MANAGER – accounts@rolexmetals.com
GENERAL INFORMATION – info@rolexmetals.com
EXPORT MANAGER – export@rolexmetals.com
IMPORT MANAGER – import@rolexmetals.com
AIR EXPORT – airexport@rolexmetals.com
SEA EXPORT – seaexport@rolexmetals.com
CUSTOMS – customs@rolexmetals.com
AIR FREIGHT – airfreight@rolexmetals.com
SEA FREIGHT – seafreight@rolexmetals.com
DESPATCH – despatch@rolexmetals.com
INSPECTION – inspection@rolexmetals.com
LOGISTICS – logistics@rolexmetals.com
TRANSPORT – transport@rolexmetals.com
KALAMBOLI WAREHOUSE – kalamboli@rolexmetals.com
TALOJA WAREHOUSE – taloja@rolexmetals.com
KHOPOLI WAREHOUSE – khopoli@rolexmetals.com
NHAVA SHEVA WAREHOUSE – nhavasheva@rolexmetals.com
KANDLA WAREHOUSE – kandla@rolexmetals.com
MUMBAI WAREHOUSE – mumbai@rolexmetals.com
STOCKYARD – stockyard@rolexmetals.com
SERVICE – service@rolexmetals.com
SUPPORT – support@rolexmetals.com
RECRUITMENT – career@rolexmetals.com
WEBMASTER – webmaster@rolexmetals.com
CUSTOMER CARE – customercare@rolexmetals.com
Note : All product names, logos, brands, trademarks and registered trademarks are property of their respective owners.
All company, product and service names used in this website are for identification purposes only.
Use of these names, trademarks and brands does not imply endorsement.