ASTM A247;Nodularity
ASTM A255;Jominy End-Quench
ASTM A262;Lab Specimen Heat Treatment
ASTM A262 (Methods A, E);IG Corrosion Susceptibility
ASTM A325;Rotational Capacity
ASTM A370;Tensile Testing
ASTM A388/A388M, A609;Ultrasonic (Contact Straight and Angle Beam)
ASTM A390 – 06(2011) ;Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)
ASTM A428/A428M;Coating Weight
ASTM A604/A604M;Macroetching
ASTM A745/A745M;Ultrasonic (Contact Straight and Angle Beam)
ASTM A763;Corrosion Susceptibility
ASTM A90;Mass of Coating
ASTM A90/A90M;Coating Weight
ASTM A923 (Method A);Corrosion Susceptibility
ASTM A956;Rockwell Hardness (A, B, C, E, 15N, 30N, 45N, 15T, 30T, 45T)
ASTM AP-200;Rockwell (HRB, HRC, 15T, 15N, 30T, 30N, 45N, 45T)
ASTM B0193;Standard Test Method for Resistivity of Electrical Conductor Materials
ASTM B117;Standard Practice for Operating Salt Spray (Fog) Apparatus
ASTM B117a;Standard Practice for Operating Salt Spray (Fog) Apparatus (Withdrawn Standard, Replaced by ASTM B117 after 2009)
ASTM B137;Coating Weight
ASTM B137-95;Standard Test Method For Measurement Of Coating Mass Per Unit Area is Anodically Coated Aluminium
ASTM B154;Standard Test Method for mercurous nitrate test for Copper Alloys
ASTM B214;Sieve Analysis of Metal Powders
ASTM B298;Continuity of Coating (Continuity Test Only)
ASTM B328 (Canceled 2006)1;Density/Porosity
ASTM B368;Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
ASTM B380;Corrosion Testing of Decorative Coatings electrodeposited by the Corrodkote Procedure
ASTM B456;discontinuous Chromium
ASTM B465;Appendix X4-Determination Of Crack Number / Number Pore
ASTM B487;Thickness
ASTM B533;Peel Strength
ASTM B557;Tensile Properties of Aluminum and Magnesium Alloys
ASTM B568;Coating Thickness by X-Ray Fluorescence (XRF) Plating Thickness
ASTM B571;Qualitative Adhesion Testing of Metallic Coatings (Except Draw Test)
ASTM B571, Section 3.8, 13;Qualitative Adhesion Testing of Metallic Coatings
ASTM B578;Microhardness of Coatings Knoop, Vickers
ASTM B604;discontinuous Chromium
ASTM B678;Solderability of Coated Products
ASTM B748;Plating/Coating Thickness
ASTM B764;Step Test
ASTM B839;Stress Durability
ASTM B954;Spectroscopy, OES (Al, Fe, Cu, Ti, Mg, Ni base)
ASTM B962;Density/Porosity
ASTM B963;Density/Porosity
ASTM C1019;Sampling and Testing Grout
ASTM C1064/C1064M;Temperature of Freshly Mixed Hydraulic-Cement Concrete
ASTM C109/C109M;(Compressive Strength Only) Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or[50-mm] Cube Specimens)
ASTM C1147;Tensile Weld Strength
ASTM C1166;Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories
ASTM C117;Materials Finer than 75-µm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM C1186 – 08(2012 ;Standard Specification for Flat Fiber-Cement Sheets
ASTM C121;Water Absorption of Slate
ASTM C1231/C1231M;Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders
ASTM C1257;Accelerated Weathering of Solvent-Release-Type Sealants
ASTM C127;Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate
ASTM C128;Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate
ASTM C1288 – 14 ;Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets
ASTM C131/C131M;Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
ASTM C1314;Compressive Strength of Masonry Prisms
ASTM C1353;Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
ASTM C136;Sieve Analysis of Fine and Coarse Aggregates
ASTM C138/C138M;Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
ASTM C140/C140M;Sampling and Testing Concrete Masonry Units and Related Units
ASTM C142;Clay Lumps and Friable Particles in Aggregates
ASTM C143/C143M;Slump of Hydraulic-Cement Concrete
ASTM C1442;Conducting Tests on Sealants Using Artificial Weathering Tests
ASTM C172/C172M;Sampling Freshly Mixed Concrete
ASTM C173;Air Content of Freshly Mixed Concrete by the Volumetric Method
ASTM C1731;Air Content of Freshly Mixed Concrete by the Volumetric Method
ASTM C192/C192M;Making and Curing Concrete Test Specimens in the Laboratory
ASTM C231/C231M;Air Content of Freshly Mixed Concrete by the Pressure Method
ASTM C29/C29M;Bulk Density (“Unit Weight”) and Voids in Aggregate
ASTM C293/C293M;Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading)
ASTM C31/C31M;Making and Curing Concrete Test Specimens in the Field
ASTM C356;Linear Shrinkage of Preformed High – Temperature Thermal Insulation Subjected to Soaking Heat
ASTM C39/C39M;Compressive Strength of Cylindrical Concrete Specimens
ASTM C393/C393M;Sandwich Beam Flexure (-150 to +350) ºF
ASTM C40;Organic Impurities in Fine Aggregates for Concrete
ASTM C42/C42M;Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
ASTM C501;Relative Resistance to Wear of unglazed Ceramic Tile by the Taber Abraser
ASTM C535;Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
ASTM C566;Total Evaporable Moisture Content of Aggregate by Drying
ASTM C584;Specular Gloss of Glazed Ceramic Whitewares and Related Products
ASTM C617/C617M;Capping Cylindrical Concrete Specimens
ASTM C642;Density, Absorption, and Voids in Hardened Concrete
ASTM C70;Surface Moisture in Fine Aggregate
ASTM C702;Reducing Samples of Aggregate to Testing Size
ASTM C765;Low Temperature Flexibility of Preformed Tape Sealants
ASTM C78/C78M;Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
ASTM C780;(ANNEX 6 only) Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry
ASTM C793;Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants
ASTM C88;Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
ASTM D 4169-09 ;Standard Practice for Performance Testing of Shipping Containers and Systems
ASTM D 4459 ;Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications
ASTM D0257;Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D0495;Standard Test MethoDfor High-Voltage, Low-Current, Dry Arc Resistance of Insulation SoliDElectrical
ASTM D0543;Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D1000;Unwind Pull
ASTM D1002;Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D1003;Procedure B Luminous Transmittance and Haze
ASTM D1004;Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D1044;Surface Abrasion of Transparent Plastics
ASTM D1052;Measuring Rubber Deterioration – Cut Growth Using Ross Flexing Apparatus
ASTM D1053;Rubber Property – Stiffening at Low Temperatures Flexible Polymers and Coated Fabrics (Tors onal Stiffness)
ASTM D1055 (15-16);Accelerated Aging Tests
ASTM D1055 (17-19);Compression Set Under Constant Deflection
ASTM D1055 (24-26);Flexing Test (Suffix H)
ASTM D1055 (27-30);Low-Temperature Test (Compression/Deflection)
ASTM D1056;compression Force
ASTM D1056 (17-23);compression Deflection
ASTM D1056 (35-42);Heat Aged Load Deflection
ASTM D1056 (43-49);Water absorption
ASTM D1056 (50-56);Compression Set Flexible Cellular Materials – Sponge or Expanded Rubber
ASTM D1056 (57-61);Low Temperature Flex
ASTM D1056 Para. 17-22;Compression-Deflection Test
ASTM D1056 Para. 42-48;Determination Of Water Absorption
ASTM D1068-10 (D);Iron Spectroscopy (UV/Vis Spectrometry)
ASTM D1117;Evaluating Nonwoven Fabrics
ASTM D1140;Amount of Material in Soils Finer than No. 200 Sieve
ASTM D1148;Rubber Deterioration-Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces and Xenon-Arc Apparatus
ASTM D1149;Rubber Deterioration Surface Ozone Cracking in a Chamber
ASTM D1149 (Method B);Ozone Resistance
ASTM D1149-A;ozone Resistance
ASTM D115;Solvent Containing Varnishes (Dielectric Strength Only)
ASTM D1171;Rubber Deterioration Surface Ozone Cracking Outdoors or Chamber (Triangular)
ASTM D1171B;Rubber Deterioration – Surface Ozone Cracking Outdoors or Chamber (Triangular)
ASTM D120;Rubber Insulating Gloves
ASTM D1200;Viscosity
ASTM D1203;Volatile Loss of Plastics Using Activated-Carbon Method
ASTM D1204;Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperatures
ASTM D1204-2;Dimensional Change
ASTM D1204-2,8;amines Contamination Resistance
ASTM D1208-96 (2012);Common Properties of Certain Pigments
ASTM D1210;Fineness of Grind
ASTM D1218;Refractive Index
ASTM D1229;Set at Low Temperatures compression
ASTM D1238;Melt Index (flow rate)
ASTM D1238-13 ;Melt Flow Rates of Thermoplastics by Extrusion Plastomer
ASTM D1242-95a;Method B Resistance of Plastic Materials to Abrasion
ASTM D1298 ;Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D1298/IP 160, API MPMS Ch 9.1 ;Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D130;Standard Test Method for corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D130/ IP154 ;Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D1319;Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D1319/ IP156 ;Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption.
ASTM D1329;Evaluating Rubber Property – Retraction at Lower Temperatures (TR Test)
ASTM D1331;Tensiometer Surface Tension
ASTM D1388;Stiffness of Fabrics
ASTM D1388-08;Standard Test Method for Stiffness of Fabrics
ASTM D1403;Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment
ASTM D1414;Rubber O-Ring Testing (Except Low Temperature Test, Mold Shrinkage)
ASTM D1415;Rubber Property – International Hardness
ASTM D1417 (Sec. 7);Tensiometer Surface Tension
ASTM D1424;Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
ASTM D1455;60° Specular Gloss of Emulsion Floor Polish
ASTM D1475;Density
ASTM D149;Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulation Materials at Commercial Power Frequencies
ASTM D1499;Filtered Open-Flame Carbon-Arc Exposures of Plastics
ASTM D150;AC Loss Characteristics and Permittivity (Dielectric Constant of Solid Electrical Insulation
ASTM D1500;Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)
ASTM D1505;Density by Density-Gradient Tube
ASTM D1505 – 10 ;Density of Plastics by the Density-Gradient Technique
ASTM D1506;Carbon Black Ash Content
ASTM D1508;Carbon Black Pelleted Fines and Attrition
ASTM D1510 Method A;Carbon Black Iodine Adsorption Number
ASTM D1512;Carbon Black pH Value
ASTM D1513;Carbon Black Pour Density
ASTM D1514;Carbon Black Sieve Residue
ASTM D1525 (Rate B);Vicat Softening Temperature of Plastics
ASTM D1557;Moisture-Density Relations (Modified Proctor)
ASTM D1598-02;Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D1599;Pressure Testing of Pipe, Tubing, and Fittings Hydrostatic Testing
ASTM D1599-99;Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D1603-12;Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D1618;Carbon Black Transmittance of Toluene Extract
ASTM D1621;Compressive Properties of Rigid Cellular Plastics
ASTM D1622;Density of Cellular Plastics Foam Density
ASTM D1630;Rubber Property – Abrasion Resistance (Footwear Abrader)
ASTM D1632;(Curing only) Making and Curing Soil-Cement Compression and Flexure Test Specimens in the Laboratory
ASTM D1633;Method A Compressive Strength of Molded Soil-Cement Cylinders
ASTM D1646;Viscosity, Stress Relaxation and Scorch Time
ASTM D1654;Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments
ASTM D1667;Test Method for Density (Suffix W)
ASTM D1667 (16-20);Compression Deflection Test Method
ASTM D1667 (21-25);Compression Set Under Constant Deflection
ASTM D1670/D1670;Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials
ASTM D1683 ;Seam Breaking Strength
ASTM D1693;Environmental Stress Cracking
ASTM D1693-12;Standard Test Method for Environmental Stress Cracking of Ethylene Plastics
ASTM D1708;Tensile Properties of Plastics
ASTM D1709;Impact Resistance of Film Dart Drop Impact
ASTM D1709-09;Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D1710;Dimensional Stability of PTFE
ASTM D1712;Resistance of Plastics to Sulfide Staining
ASTM D1735;Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D1762-84;Chemical Analysis of Wood Charcoal
ASTM D1777;Thickness of Textile Materials
ASTM D1781;Climbing Drum Peel
ASTM D1783-12 (A);Phenolic Compounds Spectroscopy (UV/Vis Spectrometry)
ASTM D1793;Spot Test Water & Soap
ASTM D1813;Thickness
ASTM D1822;Tensile impact
ASTM D1824;Apparent Viscosity Rotational Viscosity, Brookfield Viscosity
ASTM D1831;Standard Test Method for Roll Stability of Lubricating Grease
ASTM D1876;Peel Resistance T-Peel Test
ASTM D1883;CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D1894;Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D1895;Apparent Density, Bulk Factor, and for Ability of Plastic
ASTM D1922;Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D1925-772 (Withdrawn 1995);Yellowness Index of Plastics
ASTM D1938;Propagation Tear Resistance of Plastic Film and Thin Sheeting by a Single Tear
ASTM D1976-12;Standard Test Method for Elements in Water
ASTM D2084;Vulcanization by Oscillating Disk Rheometer
ASTM D2097;Newark Flex Test
ASTM D2136;Coated Fabrics – Low Temperature Bending Test
ASTM D2137;Rubber Property – Brittleness Point of Flexible Polymers and Coated Fabrics
ASTM D2166;Unconfined Compressive Strength of Cohesive Soil
ASTM D217;Standard Test Methods for Cone Penetration for Lubricant Greases
ASTM D2197;Scrape Adhesion
ASTM D2208;Breaking Strength (severe Method)
ASTM D2209;Leather, Tensile & Elongation
ASTM D2211;elongation (severe Method)
ASTM D2216;Water Content of Soil, Rock & Soil-Aggregate Mixtures
ASTM D2217-85 (1998)(Withdrawn 2007);Wet Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants
ASTM D2224;Color Measurement
ASTM D2228;Rubber Property – Relative Abrasion Resistance by Pico Abrader Method
ASTM D2240;Standard Test method for rubber propertyName Durometer Hardness
ASTM D2240 (Type A, D, M, and OO);Rubber Property – Durometer Hardness
ASTM D2240, Shore A & D;Durometer Hardness
ASTM D2244;Color Difference by Instrumental Analysis CIELAB
ASTM D2247;humidity Resistance
ASTM D2261;Tongue Tear
ASTM D2268;Standard Test Method for Analysis of High Purity n-heptane and isooctanes by Capillary Gas Chromatography
ASTM D2274;Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D2344;Short-Beam Strength of Polymer Matrix Composite Materials
ASTM D2360;Standard Test Method for Trace Impurities in mono cyclic Aromatic Hydrocarbons by Gas Chromatography
ASTM D2369-10;Volatile Contents of Coatings
ASTM D2414 (Procedures A and C);Carbon Black Oil Absorption Number (OAN)
ASTM D2419;Sand Equivalent Value of Soils and Fine Aggregate
ASTM D2435;One-dimensional Consolidation Properties of Soils
ASTM D2487;Classification of Soils for Engineering Purposes
ASTM D2488;Description and Identification of Soils (Visual-Manual Procedure)
ASTM D2500;Standard Test Method for Cloud Point of Petroleum Products
ASTM D256;Izod Pendulum Impact Resistance of Plastics
ASTM D2565;Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
ASTM D257;DC Resistance or Conductance of Insulating Materials
ASTM D2583;Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D2584;Ignition Loss of Cured Reinforced Resins
ASTM D2622;Standard Test method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spetrometry
ASTM D2624;Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
ASTM D2632;Rubber Property – Resilience by Vertical Rebound
ASTM D2699/IP237 ;Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D2700/IP236 ;Standard Test Method for Motor Oktane Number of Spark-Ignition Engine Fuel
ASTM D2732;Shrinkage of Plastic Film
ASTM D2734;Void Content of Reinforced Plastics and Composites
ASTM D276;FTIR
ASTM D2765-11;Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
ASTM D2794;Impact Resistance
ASTM D2803;Filiform Corrosion
ASTM D2837-11;Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D2850;Undrained, Unconsolidated Strength in Triaxial Compression
ASTM D2859;Ignition Characteristics of Finished Textile Floor Covering Materials
ASTM D2896;Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration
ASTM D29501;Density of Bituminous Concrete in Place by Nuclear Methods
ASTM D297;Density of Rubber (Hydrostatic Method Only)
ASTM D297 (Section 16.3);Density – Hydrostatic Method
ASTM D2990;Creep Testing
ASTM D3012;Thermal-Oxidative Stability of Propylene Plastics Using a Specimen Rotator Within in Oven
ASTM D3039;Tensile Properties of Composites
ASTM D3045;Heat Aging of Plastics Without Load
ASTM D3137;Standard Test Method for Rubber Property- Hydrolytic Stability
ASTM D3163;Strength of Adhesive Bonded Rigid Lap Shear Joints
ASTM D3167;Floating Roller Peel
ASTM D3171;Filler Content of Composite Materials (Except Microwave Digestion)
ASTM D3182;Sample Preparation
ASTM D3183;Sample Preparation
ASTM D322;Standard Test Method for Gasoline Diluent in Used Gasoline Engine Oils by Distillation
ASTM D3237;Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D3278;Flash Point
ASTM D3294;Dimensional Stability of PTFE
ASTM D3330/D3330M;Peel Adhesion of Pressure Sensitive Tape
ASTM D3338 / D3338M;Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D3343;Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D3354;Method B Blocking Load of Film by Parallel Plate Method
ASTM D3359;Tape Adhesion Test
ASTM D3359-A;X-Cut Tape Test
ASTM D3359-B;Cross-Cut Tape Test
ASTM D3363;Pencil Hardness
ASTM D3364;Flow Rates for Poly(Vinyl Chloride) with Molecular Structure Implications
ASTM D3389;Coated Fabrics Abrasion Resistance (Rotary Platform, Double Head abrade)
ASTM D3395-992 (Withdrawn 2008);Rubber Deterioration – Dynamic Ozone Cracking in a Chamber
ASTM D3418;Transition Temperature of Polymers by DSC
ASTM D3424;Standard Practice for Evaluating the Relative Light Fastness and Weatherabillity of Printed Matter
ASTM D3424 (Except Method 2);Evaluating the Relative Lightfastness and Weatherability of Printed Matter
ASTM D3479;Tension – Tension Fatigue of Composite Materials S-N Curves
ASTM D3492;Rubber Contraceptives (Male Condoms)
ASTM D3498;Adhesives for Field-Gluing Plywood to Lumber Framing for Floor Systems
ASTM D3512;Pilling Resistance (Random Tumble Pilling Tester)
ASTM D3574;Test Methods for Flexible Cellular Materials (except Test G, I4, Airflow, I2 test Dynamic Fatigue Test by Roller the Shear at Constant Force test I4 Dynamic Fatigue Test for Carpet Cushion)
ASTM D3574 (Method B1);Foam Deterioration ASTM D3574 (Method J) Indentation Force Deflection Test
ASTM D3574 (Test A);Density Test Urethane Foams
ASTM D3574 (Test C);Compression Force Deflection Test
ASTM D3574 (Test D);Constant Deflection Compression Set
ASTM D3574 (Test E);Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams – Tensile Test
ASTM D3574 (Test F);Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams – Tear Test
ASTM D3574 (Test J);Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams – Steam Autoclave Aging
ASTM D3574 (Test K);Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams – Dry Heat Aging
ASTM D3574 test C;Stress-Strain Characteristic In Compression
ASTM D3574 Test E;Tensile Test
ASTM D3574 test F;Determination Of Tear Strength
ASTM D3574 test J;Steam Autoclave Ageing
ASTM D3574, Method A;Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams
ASTM D3574, Test D, Compression Set At;StandardConditioning Temperature
ASTM D3575;Test Methods for Flexible Cellular Materials Made From Olefin (Except Sections 34-35, 45-46, 49-50, 66-67)
ASTM D3575 – Suffix L (Sections 26-32);Flexible Cellular Materials Made From Olefin Polymers – Water Absorption
ASTM D3575 (Section 17-24);Flexible Cellular Materials Made From Olefin Polymers – Compression Deflection
ASTM D3575 (Section 9-16);Flexible Cellular Materials Made From Olefin Polymers – Compression Set Under Constant Deflection
ASTM D3575( Suffix W);Density – Flexible Cellular Materials Made From Olefin Polymers
ASTM D3575-Suffix S (Section 35-42);Flexible Cellular Materials Made From Olefin Polymers – Thermal Stability
ASTM D3577;Rubber Surgical Gloves
ASTM D3578;Rubber Examination Gloves
ASTM D3641;Injection Molding Test Specimens of Thermoplastics Molding and Extrusion Materials
ASTM D3652/D3652M;Thickness of Pressure Sensitive Tapes
ASTM D3665;Random Sampling of Construction Materials
ASTM D3677;Rubber – Identification by Infrared spectrophotometry
ASTM D3703;Standard Test Method for hydroperoxides Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels
ASTM D374;Methods A-C Thickness of Electrical Insulation
ASTM D3759/3759M;Breaking Strength and Elongation of Pressure Sensitive Tape (Procedure A)
ASTM D3763;Standard Test Method for High Speed ??Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D3767;Standard Practice for Rubber – Measurement of Dimensions
ASTM D3767 # 9 (A, A1, A2);Standard Practice for Rubber Measurement of Dimensions
ASTM D3767-A;Determination Of Thickness
ASTM D3767-A 1;Alternating Ultraviolet Radiation / Humidity Resistance Test
ASTM D3769;heat sag
ASTM D3776;Mass Per Unit Area (Weight) of Fabric
ASTM D3776 Option C ;Mass per Unit of Fabric – Option C
ASTM D3786 ;Bursting Strength of Textile Fabrics . Diaphragm
ASTM D380;Rubber Hose for Automotive Air and Vacuum Brake Systems
ASTM D3801;Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D381;Standard Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D381 ;Standard Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D3815;Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
ASTM D3828;Flash Point
ASTM D3833/3833M;Water Vapor Transmission of Pressure Sensitive Tape
ASTM D3846;In-Plane Shear Strength of Reinforced Plastics
ASTM D3850;Thermogravimetric Analysis (TGA Analysis)
ASTM D3882;Bow and Skew
ASTM D3884;Standard Guide for Abrasion Resistance of Textile Fabrics (Rotary Platform, Double-Head Method)
ASTM D3887 Para. 12;Determination Of The Number Of Wales And Stitch Racing
ASTM D3895;Oxidative Induction Time of Polyolefins by Thermal Analysis
ASTM D3895-07;Standard Test Method for Oxidative Induction Time of Polyolefins by Differential Scanning Calorimetry
ASTM D3939;Mace Snag Test
ASTM D395;Rubber Property-Compression Set (Method B)
ASTM D395 (Method B);Compression Set
ASTM D395, Method B;Rubber Property Compression Set
ASTM D395-B;compression Set
ASTM D3985-05;Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D4014;Shear Modulus and Related Testing for Elastomeric Bridge Bearings
ASTM D4014 (Except 8.2.3, 8.2.5 & 8.2.6);Plain and Steel-Laminated Elastomeric Bearings for Bridges
ASTM D4017;Moisture Content by Karl Fischer Titration
ASTM D4039;Reflection Haze of High-Gloss Surfaces
ASTM D4048;Standard Test Method for Detection of Copper Corrosion from Lubricating Grease
ASTM D4052;Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D4052 ;Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D4052 (Manual);Density / API Gravity
ASTM D4060;Abrasion Resistance Organic Coatings by the Taber Abraser
ASTM D4060, D3884;Taber Abrasion
ASTM D4060-10;Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D4065;Plastics Dynamic Mechanical Properties Determination and Report of Procedures
ASTM D412;Vulcanized Rubber and Thermoplastic Elastomers – Tension
ASTM D413;Rubber Property-Adhesion to Flexible Substrates
ASTM D4138;Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means
ASTM D413-A;Adhesion Test (Type A)
ASTM D4157;Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)
ASTM D4176;Appearance
ASTM D4176 ;Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels(Visual Inspection Procedures)
ASTM D421;Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants
ASTM D4212;Paint Viscosity – Zahn
ASTM D422;Particle-Size Analysis of Soils
ASTM D4226;Impact Resistance of Rigid Poly(Vinyl Chloride) Building Products
ASTM D4239-14e2 ;Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion
ASTM D429;Rubber Property – Adhesion to Rigid Substrates
ASTM D429 (Method A);Adhesion
ASTM D4294 ;tandard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D430;Rubber Deterioration – Dynamic Fatigue
ASTM D4318;Liquid Limit, Plastic Limits & Plasticity Index of Soils
ASTM D4329;UV Exposure of Plastics QUV
ASTM D434 ;Resistance of Yarns to Seam Slippage
ASTM D4440;Rheological Measurements of Polymer Melts Using Dynamic Mechanical Procedures
ASTM D4442 – 15 ;Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D4444 – 13 ;Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
ASTM D445;Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D445 ;Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D4459;Xenon-Arc Exposure of Plastics Intended for Indoor Applications
ASTM D446;Standard Specifications and Operating Instructions for Glass Capillary Kinematic viscometer
ASTM D4482;Rubber Property – Extension Cycling Fatigue
ASTM D4530;Standard Test Method for Determination of Carbon Residue (Micro Method)
ASTM D454;Rubber Deterioration by Heat and Air Pressure
ASTM D4546;One-Dimensional-Swell or Settlement Properties of Cohesive Soils
ASTM D4587;UV Exposure of Coatings QUV
ASTM D4591;Heats of Transitions of Flouropolymers by DSC
ASTM D4603-03;Standard Test Method for Determining Inherent Viscosity of Poly (Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D4632-08;Standard Test Method for serious Breaking Load and Elongation of Geotextiles
ASTM D4637/D4637M, (Sections 8.19 & 8.20);Weather Resistance of EPDM Sheet Used in Single-Ply Roof Membrane
ASTM D4643;Determination of Water (Moisture) Content of Soil by Microwave Oven Heating
ASTM D4674 (Method IV);Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
ASTM D4683;Standard Test Method for Measuring Viscosity of New and Used Engine Oils at High Shear Rate and High Temperature by Tapered Bearing Simulator Viscometer at 150 ° C
ASTM D4684;Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D4703;Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D4703 – 10a ;Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D471;Rubber Property-Effect of Liquids
ASTM D4737;Standard Test Method for Calculated Cetane Index by Four Variable Equation in connection with 1.2.2 and 1.2.3
ASTM D4737 ;Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D4739;Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D4745 (Section 11.3);Bulk Density
ASTM D4745 (Section 11.4), ASTM D1708;Tensile Properties
ASTM D4745 (Section 11.5), ASTM D792;Specific Gravity
ASTM D4745 (Section X1.3);Shrinkage and Growth
ASTM D4798/D4798M;Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
ASTM D4799;Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV,Water Spray, and Condensation Method)
ASTM D4804;Flammability of Films
ASTM D4812;Unnotched Cantilever Beam Impact Strength of Plastics
ASTM D4815;Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C1 to C4 Alcohols in Gasoline by Gas Chromatography (Withdrawn
ASTM D482;Standard Test Method for Ash from Petroleum Products
ASTM D483-04 ;tandard Test Method for Unsulfonated Residue of Petroleum Plant Spray Oils
ASTM D4886-10;Standard Test Method for Abrasion Resistance of Geotextiles (Sand Paper / Sliding Block Method)
ASTM D4894 (Section 10.2);Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D4952 ;Standard Test Method for Qualitative Analysis for Active Sulfur Species in Fuels and Solvents (Doctor Test)
ASTM D4966;Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method) Chrysler LP-463PB-54-01 Crock Mar Resistance
ASTM D4970;Pilling Resistance and Other Related Surface Changes of Textile Fabrics Martindale Tester
ASTM D4972;pH of Soils
ASTM D5006;Fuel System Icing Inhibitors Refractometry
ASTM D5034;Tensile Strength
ASTM D5034 ;Breaking Strength and Elongation (Grab Test) Breaking Strength Only
ASTM D5035;Breaking Strength, Textile Fabrics, Strip Method
ASTM D5071;Exposure of Photodegradable Plastics in a Xenon Arc Apparatus
ASTM D5132;Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles
ASTM D5134;Standard Test Method for Detailed Analysis of Petroleum naphtha through n-nonanes by Capillary Gas Chromatography
ASTM D5151;Detection of Holes in Medical Gloves
ASTM D5178;Mar Resistance of Coatings
ASTM D518;Rubber Deterioration-Surface Cracking
ASTM D5182;Standard Test method for Evaluating the Scuffing Load Capacity of Oils (FZG Visual Method)
ASTM D5185;Standard Test Method for Determination of additives may Elements, Wear Metals and Contaminants in Used Lubricating Oils and Determination of the Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D518-992 (Withdrawn 2008);Rubber Deterioration – Surface Cracking
ASTM D5191;Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D5191 ;Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D5208;Fluorescent Ultraviolet (UV) Exposure of Photodegradable Plastics
ASTM D5215;Instrumental Evaluation of Staining of Vinyl Flooring by Adhesives
ASTM D522;Method B Mandrel Bend Test of Coatings
ASTM D523;Standard Test Method for Specular Gloss
ASTM D525/ IP40 ;Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method)
ASTM D5250;Poly(vinyl chloride) Gloves for Medical Application
ASTM D5261-10;Standard Test Method for Measuring Mass per Unit Area of ??Geotextiles
ASTM D5279;Dynamic Mechanical Properties of Plastics Using Twist
ASTM D5289;Rubber Property – Vulcanization Using Rotorless Cure Meters
ASTM D5293;Standard Test Method for Apparent Viscosity of Engine Oils Between -10 and -35 ° C Using Cold- Cranking Simulator
ASTM D5355-95 (2012);Specific Gravity of Oils and Liquid Fats
ASTM D53611;Sampling Compacted Bituminous Mixtures for Laboratory Testing
ASTM D5373-14e1 ;Standard Test Methods for Determination of Carbon, Hydrogen and Nitrogen in Analysis Samples of Coal and Carbon in Analysis Samples of Coal and Coke
ASTM D5397-07;Standard Test Method for Evaluation of Stress Crack Resistance of Polyolefin Geomembranes Using Notched Constant Tensile Load Test
ASTM D542;Index of Refraction Refractive Index, Refractometer
ASTM D5420;Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Hammer (Gardner Impact)
ASTM D5427 Para. 8.4;Accelerated Aging (Aging Cycle)
ASTM D543;Resistance of Plastics to Chemical Reagents
ASTM D5452;Particulate Contamination Gravimetric
ASTM D5453;Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D5453 ;tandard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D5483;Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry
ASTM D5501;Standard Test Method for Determination of ethanol and methanol happy in Greater Fuels Containing 20% ??ethanol by gas chromatography
ASTM D558;Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures
ASTM D5580;Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, p / m-Xylene, o-Xylene, C9 and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography
ASTM D5587;Tearing Strength of Fabrics by the Trapezoid Procedure
ASTM D5587 / ASTM D5733 ;Trapezoidal Tear Strength
ASTM D5596-03;Standard Test Method for Microscopic Evaluation of the Dispersion of Carbon Black in Polyolefin Geosynthetics
ASTM D56;Flash Point
ASTM D5617-04;Standard Test Method for Multi-Axial Tension Test for Geosynthetics
ASTM D5628;Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM D5630 Method B;Ash Content Filler Content
ASTM D5630, Method B;Ash glad of Thermoplastics
ASTM D5668 (Method A);Rubber From Synthetic Sources – Volatile Matter
ASTM D570;Water Absorption
ASTM D570 / ISO 62;Determination Of Water Absorption
ASTM D570-98;Standard Test Method for Water Absorption of Plastics
ASTM D5712;Lowry Protein Assay Chemical Analysis for Total Aqueous Protein
ASTM D572;Rubber – Deterioration by Heat and Oxygen
ASTM D5729;Standard Test Method for Thickness of Nonwoven Fabrics
ASTM D573;Rubber-Deterioration in Air Oven
ASTM D5733;Tearing Strength of Nonwoven Fabrics by the Trapezoid Procedure
ASTM D5734-012 (Withdrawn 2008);Tearing Strength of Nonwoven Fabrics by FallingPendulum (Elmendorf) Apparatus
ASTM D5735-012 (Withdrawn 2009);Tearing Strength of Nonwoven Fabrics by the Tongue (Single Rip) Procedure
ASTM D575;Rubber Properties in Compression
ASTM D5773;Cloud Point
ASTM D5845 ;Standard Test Method for Determination of MTBE,ETBE, TAME, DIPE, Methanol, Ethanol and tert-Butanol in Gasoline by Infrared Spectroscopy
ASTM D5865 ;Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D5887-09;Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall permeameter
ASTM D5890-11;Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners
ASTM D5946;Contact Angle Determination
ASTM D5947;Physical Dimensions of Solid Plastics Specimens
ASTM D5949;Pour Point
ASTM D5963;Rubber Properties – Abrasion Resistance (Rotary Drum Abrader)
ASTM D5963 (Methods A & B);Abrasion Resistance
ASTM D5972;Freeze Point
ASTM D5992;Dynamic Testing of Vulcanized Rubber and RubberLike Materials Using Vibratory Methods
ASTM D6079;Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High Frequency Reciprocating Rig (HFRR)
ASTM D6082;Standard Test Method for High Temperature Foaming Characteristics of Lubricating Oils
ASTM D610;Evaluating Degree of Rusting on Painted Steel Surfaces
ASTM D6100;Dimensional Stability of POM (Acetal)
ASTM D6110;Impact Resistance of Notched Specimens of Plastics
ASTM D6124;Residual Powder on Medical Gloves
ASTM D613/ IP41 ;Standard Test Method for Cetane Number of Diesel Fuel Oil
ASTM D6147;Sealability of Gasket Materials
ASTM D618;Conditioning Plastics
ASTM D618-08;Standard Practice for Conditioning Plastics for Testing
ASTM D6182;Flexibility and Adhesion of Finish on Leather
ASTM D621;Deformation Under Load
ASTM D6217;Particulate Contamination Gravimetric
ASTM D622;Standard Test Method for Rubber Hoses
ASTM D623;Heat Generation and Flexing Fatigue in Compression
ASTM D624;Tear Strength Tear Resistance
ASTM D624 (Die C);Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomer
ASTM D6243-13;Standard Test Method for Determining the Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method
ASTM D6261;Dimensional Stability of Polyester
ASTM D6284;Rubber Property – Effect of Aqueous Solutions with Available Chlorine and Chloramine
ASTM D6304;Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM D6304 (Procedure A);Water by Karl Fischer Titrametric
ASTM D6319;Nitrile Examination Gloves for Medical Application
ASTM D6324;Male Condoms Made from Polyurethane
ASTM D635;Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
ASTM D635-10;Standard Test Method for Rate of Burning and / or Extent and Time of Burning of Plastics in a Horizontal Position
ASTM D6370;Rubber Analysis by TGA
ASTM D6371;Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels
ASTM D638;Tensile Properties
ASTM D6413 ;Flame Resistance of Textiles (Vertical Test)
ASTM D6413 ;NFPA 2112 Section 8.3 Flame Resistance of Textiles (Vertical Test) Heat & Thermal Shrinkage
ASTM D644;Moisture Content of Paper & Paperboard
ASTM D6443;Test Method for Determination of calcium, chlorides rine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectro metry (Mathematical Correction Procedure)
ASTM D648;Method B Heat Deflection Temperature (HDT, DTUL)
ASTM D6492;Hexavalent Chromium (Hex Chrome, Cr VI) Detection by Spot Test
ASTM D6496-04a;Standard Test Method for Determining Average Bonding Peel Strength Between the Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners
ASTM D6499;ELISA Protein Assay Chemical Analysis for Antigenic Protein Content
ASTM D6575-00;Standard Test Method for Determining Stiffness of Geosynthetics Used as Turf Reinforcement Mats (TRMS)
ASTM D6594;Standard Test Method for Evaluation of corrosiveness of diesel engine oil at 135 ° C
ASTM D6595;Wear Metals of Oil Samples Emissions Spectroscopy
ASTM D6637-11;Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
ASTM D664;Standard Test method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D664 (Method A);Acid Number Titrametric
ASTM D6660;Freeze Point
ASTM D6662 (Section 6.3);Polyolefin-Based Plastic Lumber Decking Boards
ASTM D6693;Standard Test Method for Determining Tensile Properties of Non-reinforced polyethylene and non-reinforced polypropylenes Flexible Geomembrane
ASTM D6695;Xenon-Arc Exposure of Paint and Related Coatings
ASTM D6754 (Section 8.15);Ketone Ethylene Ester Based Sheet Roofing
ASTM D6754/D6754M;Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
ASTM D6839;Standard Test Method for Hydrocarbon Types, Oxygenated Compounds and Benzene in Spark Ignition Engine Fuels by Gas Chromatography
ASTM D6869;Moisture Content of Plastics by Karl Fischer Titration
ASTM D6878/D6878M, (Section 7.13);Weather Resistance of Thermoplastic Polyolefin Based Roofing
ASTM D689;Standard Test Method for Internal Tearing Resistance of Paper
ASTM D6892;Standard Test Method for Pour Point of Petroleum Products (Robotic Tilt Method)
ASTM D6905;Elongation by Impact
ASTM D6938;In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
ASTM D695;Compressive Properties of Rigid Plastics
ASTM D696;Coefficient of Linear Thermal Expansion of Plastics Between (-30 30 C?)
ASTM D6971 ;Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D6977;Polychloroprene Examination Gloves for Medical Application
ASTM D698;Moisture-Density Relations (Standard Proctor)
ASTM D7039;Sulfur X-Ray Fluorescence
ASTM D7091;Standard Practice for Nondestructive Measurement of Dry Film Thickness of nonmagnetic Coatings Applied to Ferrous Metals and nonmagnetic, nonconductive Coatings Applied to Nonferrous Metals
ASTM D7111;Standard Test Method for Determination of Trace Elements in Middle Distillate Fuels by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D7121;Rubber Property – Resilience Using Schob Type Rebound Pendulum
ASTM D714;Evaluating Degree of Blistering of Paints
ASTM D7198;Disposable Embalming Gloves for Single-Use Applications
ASTM D732;Shear Strength of Plastics by Punch Tool
ASTM D7334;Contact Angle Determination
ASTM D7344 ;Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Mini Method)
ASTM D737;Air Permeability of Fabrics, Milling Method
ASTM D7427;Immunological Measurement of Four Principal Allergenic Proteins (Hev b 1, 3, 5 and 6.02) in Natural Rubber and its Products Derived from Latex
ASTM D746;Brittleness Temperature of Plastics and Elastomer by Impact
ASTM D7466-10;Standard Test Method for Measuring the Height of Textured Geomembrane asperity
ASTM D747;Apparent Bending Modulus of Plastics by Means of a Cantilever Beam
ASTM D7490;Contact Angle Determination
ASTM D75;Sampling Aggregates
ASTM D750;Rubber Deterioration Using Artificial Weathering Apparatus
ASTM D751;Sampling Aggregates Cement
ASTM D751 Para. 11-15;Breaking Strength Test Method serious
ASTM D751 Para. 50-53;adhesion
ASTM D7525;Standard Test Method for Oxidation Stability of Spark Ignition Fuel Rapid Small Scale Oxidation Test (RSSOT) (Withdrawn
ASTM D7545;Standard Test Method for Oxidation Stability of Middle Distillate Fuels Rapid Small Scale Oxidation Test (RSSOT)
ASTM D7582 ;Standard Test Methods for Proximate Analysis of Coal and Coke by Macro Thermogravimetric Analysis
ASTM D7596;Particle Count
ASTM D7661;Determining Compatibility of Personal Lubricants with Natural Rubber Latex Condoms
ASTM D774;Bursting Strength of Paper
ASTM D7774;Flexural Fatigue Properties of Plastics
ASTM D7791;Unaxial Fatigue Properties of Plastics Tensile Fatigue of Plastics
ASTM D785;Rockwell Hardness of Plastics (Scales R, L, M, E, K)
ASTM D785 (Scale R);Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D7869;Xenon Arc Exposure Test with Enhanced Light and Water Exposure for Transportation Coatings
ASTM D790;Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D792;Density
ASTM D792, Method A;Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D792-08;Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D794 2 (Withdrawn 1998);Determining Permanent Effect of Heat on Plastics
ASTM D813;Rubber Deterioration – Crack Growth
ASTM D814;Rubber Property – Vapor Transmission of Volatile Liquids GM 214M2 (Withdrawn 2013) Tables 2 (3.1.3) Tables 1, 2, 3 and 4 (3.1.2 – 3.1.4) Engine Intake Manifold and Throttle Body Gaskets
ASTM D822;Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings
ASTM D828;Tensile Breaking Strength of Paper & Paperboard
ASTM D832;Rubber Conditioning for Low Temperature Testing
ASTM D854;Specific Gravity of Soils
ASTM D86;Test Method for Distillation of Petroleum Products at Atmospheric Pressure
ASTM D86 ;Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure
ASTM D865;Rubber-Deterioration by Heat in Air (Test Tube Enclosure)
ASTM D870;Testing Water Resistance of Coatings Using Water Immersion
ASTM D876 (Section 59, 60, 62);Volume Resistivity – Non-rigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
ASTM D882;Tensile Properties Thin Plastic Sheeting
ASTM D885 Para. 16, 18, 19;Tensile Properties of Yarns
ASTM D885-X2.4;Shrinkage Behaviour In Hot Air
ASTM D891 Method A;Specific Gravity,
ASTM D892;Standard Test Method for Foaming Characteristics of Lubricating Oils
ASTM D896;Resistance To Chemical Reagents
ASTM D897;Tensile Properties of Adhesive Bonds
ASTM D903;Peel Strength 180º Peel, Adhesive Bonding, Stripping Strength
ASTM D904 (Method A);Rubber Deterioration Using Artificial Weathering Apparatus
ASTM D92;Test Method for Flash and Fire Points by Cleveland Open Cup Tester
ASTM D925;Rubber Property – Staining of Surfaces Contact, Migration and Distribution
ASTM D925 Method A;Staining of Surfaces (Contact / migration / diffusion)
ASTM D93;Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D93 (Procedure A);Pensky Martens Flash Point
ASTM D945;Rubber Properties in Compression or Shear (Mechanical Oscillograph)
ASTM D952;Bond of Cohesive Strength of Sheet Plastics & Electrical Insulation
ASTM D953;Bearing Strength
ASTM D968;Abrasion Resistance by Falling Abrasive Falling Sand Abrasion
ASTM D97;Standard Test Method for Pour Point of Petroleum Products
ASTM D971;Tensiometer Surface Tension
ASTM D974;Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D974-14e1 ;Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D976;Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D976 ;Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D9791;Sampling Bituminous Paving Mixtures
ASTM D991;Volume Resistivity of Electrically Conductive and Antistatic Products
ASTM E10;Standard Test Method for Brinell Hardness of Metallic Materials
ASTM E1004;Electrical Conductivity
ASTM E1019;Oxygen/Nitrogen/Hydrogen Determination
ASTM E1064;Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration
ASTM E1077;Carburization/Decarburization
ASTM E1086;Spectroscopy, OES (Al, Fe, Cu, Ti, Mg, Ni base)
ASTM E111;Young’s Modulus (Tension and Compression)
ASTM E112;Standard Test Methods for Determining Average Grain Size
ASTM E1131;Compositional Analysis by thermogravimetric, TGA
ASTM E114;Ultrasonic Pulse-Echo Straight-Beam Contact Testing
ASTM E1164;Obtaining Spectrometric Data for Object-Color Evaluation
ASTM E1181;Grain Size
ASTM E119;Fire test
ASTM E1251;Spectroscopy, OES (Al, Fe, Cu, Ti, Mg, Ni base)
ASTM E1252;FTIR, Qualitative Analysis
ASTM E1252-98 (2013);Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
ASTM E1268;Microstructure Evaluation
ASTM E1304;Fracture Toughness
ASTM E132;Poisson’s Ratio
ASTM E1331;Reflectance Factor and Color by Spectrophotometry Using a Hemispherical Geometry
ASTM E1348;Color by Spectrophotometry Using Hemispherical Geometry
ASTM E1356;Glass Transition Temperature by DSC
ASTM E140;Hardness Rockwell (A, B, C, 15N, 30N, 45N, ASTM E18, E140 15T, 30T, 45T)
ASTM E1409;Oxygen/Nitrogen/Hydrogen Determination
ASTM E1417/E1417M;Liquid Penetrant Inspection (Water Washable Fluorescent)
ASTM E1418;Liquid Penetrant (Fluorescent)
ASTM E1444;Magnetic Particle Inspection (Bench Fluorescent)
ASTM E1444/E1444M;Magnetic Particle (Bench Wet Fluorescent,Yoke Dry Visible and Wet Fluorescent)
ASTM E1447;Oxygen/Nitrogen/Hydrogen Determination
ASTM E1453;Computed Radiography
ASTM E1508;EDS in SEM (Semi-Quantitative)
ASTM E160-80 ;Test Method for Combustible Properties of Treated Wood by the Crib Test (Withdrawn 1993)
ASTM E162 – 15a ;Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
ASTM E1627 ;Standard Practice for Sensory Evaluation of Edible Oils and Fats
ASTM E164;Contact Ultrasonic Testing of Weldments
ASTM E165/E165M;Liquid Penetrant (Fluorescent)
ASTM E1742/E1742M;Radiography (X-ray Film)
ASTM E176 ;Terminology of Fire Standards
ASTM E18;Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E18 Leeb Portable Hardness ASTM A956;Rockwell Hardness (A, B, C, E, 15N, 30N, 45N, 15T, 30T, 45T)
ASTM E190;Bend
ASTM E1999;Spectroscopy, OES (Al, Fe, Cu, Ti, Mg, Ni base)
ASTM E2002;Computed Radiography
ASTM E2007;Computed Radiography
ASTM E2104;Radiography (X-ray Film)
ASTM E2231 ;Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
ASTM E224-08;Analysis for Hydrochloric Acid
ASTM E23;Impact Properties (Charpy) (-320 ºF to RT)
ASTM E2339;Computed Radiography
ASTM E2404 ;Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) Wall or Ceiling Coverings, and of Facings and Wood Veneers Intended to be Applied on Site Over a Wood Substrate, to Assess Surface Burning Characteristics
ASTM E2412;Oils Trend Analysis FTIR Spectroscopy
ASTM E2445/E2445M;Computed Radiography
ASTM E2573 ;Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics
ASTM E2579 ;Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
ASTM E2599 ;Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics
ASTM E2688 ;Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics
ASTM E2690 ;Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics
ASTM E2768 ;Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)
ASTM E286 ;Test Method for Surface Flammability of Building Materials Using an 8-ft (2.44-m) Tunnel Furnace
ASTM E290;Bend
ASTM E291-09;Total Alkalinity of Caustic Soda and Caustic Potash
ASTM E2988 ;Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics
ASTM E3;Sample Preparation
ASTM E308 – 13 ;Computing the Colors of Objects by Using the CIE System
ASTM E313;Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
ASTM E340;Surface Discontinuities
ASTM E359-10;Analysis or the Total Alkalinity Soda Ash
ASTM E381;Macrostructure
ASTM E384;Standard Test Method for Knoop and Vickers Hardness of material
ASTM E407;Microetching
ASTM E415;Spectroscopy, OES (Al, Fe, Cu, Ti, Mg, Ni base)
ASTM E449-08 (2013);Analysis of Calcium Chloride
ASTM E45;Standard Test Methods for Determining the Inclusion Content of Steel
ASTM E45 (Method A);Inclusion Rating
ASTM E45 (Methods A, E);Inclusion Ratings
ASTM E466;Fatigue Testing (-300 to +600) ºF, (1 to 50) Hz
ASTM E517;r-Value (Plastic Strain Ratio)
ASTM E562;Volume Percent
ASTM E605/E605M;Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members
ASTM E606;Fatigue Testing, Strain Controlled
ASTM E646;n-Value (Strain Hardening Exponent)
ASTM E662;Optical Smoke Density
ASTM E69 – 02 ;Standard Test Method for Combustible Properties of Treated Wood by the Fire-Tube Apparatus
ASTM E70;Aqueous Solutions with Glass Electrode
ASTM E709;Magnetic Particle Testing
ASTM E736/E736M;Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
ASTM E794;Differential Scanning Calorimetry (DSC) Melting Point, Crystallization Temperature
ASTM E8;Tension Testing of Metals
ASTM E8 / E8M;Tensile Testing
ASTM E8/E8M;Tension (= 60 klbs)
ASTM E831;Thermomechanical Analysis (TMA) Thermal Expansion, CTE, CLTE Probe Types Expansion, Penetration, Tension (Film/Fiber), 3-Point Bend
ASTM E84;Fire test
ASTM E84 – 15a ;Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM E9;Compression (= 60 klbs)
ASTM E92-82 (2003);Microhardness-Vickers (100-2000)gf
ASTM E930;Grain Size
ASTM E94;Radiography (X-ray Film)
ASTM E96;Water Vapor Transmission
ASTM E96 / E96M-10;Standard Test Methods for Water Vapor Transmission of Materials
ASTM E96/E96M;Water Vapor Transmission of Material
ASTM EN 71-1;2011 (Section 8.8) Bite 16 CFR 1500.50, 1500.51(c), 1500.52(c), 1500.53(c)
ASTM F1112;Statics Testing of Tubeless Pneumatic Tires for Rate of Loss of Inflation Pressure
ASTM F1292;Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment
ASTM F1292-09;Standard Specification for Impact Attenuation of Surfacing Materials dans le Use Zone of Playground Equipment
ASTM F1342 (Procedure A);Protective Clothing Material Resistance to Puncture
ASTM F146;Fluid Resistance of Gasket Materials
ASTM F147;Flexibility of Non-Metallic Gasket Materials
ASTM F1506 ;Standard Performance Specification for Flame Resistant and Arc Rated Textile Materials for Wearing Apparel for Use by Electrical Workers Exposed to Momentary Electric Arc and Related Thermal Hazards
ASTM F1515 (Water Cooled Xenon only);Measuring Light Stability of Resilient Flooring by Color Change
ASTM F152;Tension Testing of Nonmetallic Gasket Materials
ASTM F1914 ;Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering
ASTM F2111;Intergranular Attack (IGA) and End Grain Pitting
ASTM F2328;Decarburization
ASTM F2894 ;Heat & Thermal Shrinkage
ASTM F36;Compressibility and Recovery of Gasket Materials
ASTM F483;Total Immersion Corrosion
ASTM F606;Wedge
ASTM F606M;Fastener Tensile up to 30000 lbs Axial
ASTM F693-08 (Section 4.7);Sharp Edges / Accessible Edges
ASTM F788;Discontinuities
ASTM F788M;Surface Discontinuities
ASTM F812;Discontinuities
ASTM F88;Seal Strength of Films
ASTM F963-08 (Section 4.1);Material Quality
ASTM F963-08 (Section 4.10);Wires and/or Rods
ASTM F963-08 (Section 4.11);Nails and Fasteners
ASTM F963-08 (Section 4.12);Plastic Film
ASTM F963-08 (Section 4.13);Folding Mechanisms and Hinges
ASTM F963-08 (Section 4.14);Cords, Straps and Elastics
ASTM F963-08 (Section 4.15);Stability and Over-Load Requirements
ASTM F963-08 (Section 4.16);Confined Spaces
ASTM F963-08 (Section 4.17);Wheels, Tires and Axles
ASTM F963-08 (Section 4.18);Holes, Clearances and Accessibility of Mechanisms
ASTM F963-08 (Section 4.19);Simulated Protective Devices
ASTM F963-08 (Section 4.2, Annex A4 and Annex A6);Flammable Solids / Removable Wear
ASTM F963-08 (Section 4.20.1);Pacifiers with Rubber Nipples
ASTM F963-08 (Section 4.20.2);Toy Pacifiers
ASTM F963-08 (Section 4.21);Projectile Toys
ASTM F963-08 (Section 4.22);Teethers and Teething Toys
ASTM F963-08 (Section 4.23.1);Rattles with Nearly Spherical Hemispherical, or Circular Flared Ends
ASTM F963-08 (Section 4.24);Squeeze Toys
ASTM F963-08 (Section 4.25);Battery Operated Toys
ASTM F963-08 (Section 4.26);Toys Intended to be Attached to a Crib or Playpen
ASTM F963-08 (Section 4.27);Stuffed and Beanbag-Type Toys
ASTM F963-08 (Section 4.3.7);Stuffing Materials
ASTM F963-08 (Section 4.30);Toy Gun Marking
ASTM F963-08 (Section 4.32);Certain Toys with Nearly Spherical Ends
ASTM F963-08 (Section 4.34);Small Balls
ASTM F963-08 (Section 4.35);Pompoms
ASTM F963-08 (Section 4.36);Hemispheric-Shaped Objects
ASTM F963-08 (Section 4.38);Magnets
ASTM F963-08 (Section 4.39);Jaw Entrapment in Handles and Steering Wheels
ASTM F963-08 (Section 4.4);Electronically Operated Toys
ASTM F963-08 (Section 4.5);Sound Producing Toys (Including Cap and Toy Guns)
ASTM F963-08 (Section 4.6);Small Parts Rule / Small Objects
ASTM F963-08 (Section 4.6.3);Labeling of Misbranded Toys
ASTM F963-08 (Section 4.8);Projections
ASTM F963-08 (Section 4.9);Sharp Points / Accessible Points
ASTM F963-08 (Section 5.4);Aquatic Toys
ASTM F963-08 (Section 8.10);Compression
ASTM F963-08 (Section 8.12);Flexure
ASTM F963-08 (Section 8.5);Use and Abuse Testing Normal Use Testing
ASTM F963-08 (Section 8.7);Impact / Drop Test
ASTM F963-08 (Section 8.8);Torque
ASTM F963-08 (Section 8.9);Tension
ASTM F963-11 (Section 4.1);Material Quality
ASTM F963-11 (Section 4.10);Wires and/or Rods
ASTM F963-11 (Section 4.11);Nails and Fasteners
ASTM F963-11 (Section 4.12);Plastic Film
ASTM F963-11 (Section 4.13);Folding Mechanisms and Hinges
ASTM F963-11 (Section 4.14);Cords, Straps and Elastics
ASTM F963-11 (Section 4.15, except 4.15.6);Stability and Over-Load Requirements
ASTM F963-11 (Section 4.16);Confined Spaces
ASTM F963-11 (Section 4.17);Wheels, Tires and Axles
ASTM F963-11 (Section 4.18);Holes, Clearances and Accessibility of Mechanisms
ASTM F963-11 (Section 4.19);Simulated Protective Devices
ASTM F963-11 (Section 4.2, Annex A5 and Annex A6);Flammable Solids / Removable Wear
ASTM F963-11 (Section 4.20.1);16 CFR Part 1511
ASTM F963-11 (Section 4.20.2);16 CFR Part 1511
ASTM F963-11 (Section 4.21);Projectile Toys
ASTM F963-11 (Section 4.22);Teethers and Teething Toys
ASTM F963-11 (Section 4.23.1);Rattles with Nearly Spherical Hemispherical, or Circular Flared Ends
ASTM F963-11 (Section 4.24);Squeeze Toys
ASTM F963-11 (Section 4.25);Battery Operated Toys
ASTM F963-11 (Section 4.26);Toys Intended to be Attached to a Crib or Playpen
ASTM F963-11 (Section 4.27);Stuffed and Beanbag-Type Toys
ASTM F963-11 (Section 4.3.7);Stuffing Materials
ASTM F963-11 (Section 4.30);Toy Gun Marking
ASTM F963-11 (Section 4.32);Certain Toys with Nearly Spherical Ends
ASTM F963-11 (Section 4.34);Small Balls
ASTM F963-11 (Section 4.35);Pompoms
ASTM F963-11 (Section 4.36);Hemispheric-Shaped Objects
ASTM F963-11 (Section 4.38);Magnets
ASTM F963-11 (Section 4.39);Jaw Entrapment in Handles and Steering Wheels
ASTM F963-11 (Section 4.4);16 CFR 1505
ASTM F963-11 (Section 4.5);Sound Producing Toys (Including Cap and Toy Guns)
ASTM F963-11 (Section 4.6);Small Parts Rule / Small Objects
ASTM F963-11 (Section 4.6.3);Labeling of Misbranded Toys
ASTM F963-11 (Section 4.7);Sharp Edges / Accessible Edges
ASTM F963-11 (Section 4.8);Projections
ASTM F963-11 (Section 4.9);Sharp Points / Accessible Points
ASTM F963-11 (Section 5.4);Aquatic Toys
ASTM F963-11 (Section 8.10);16 CFR 1500.50, 1500.51g, 1500.52g, 1500.53g
ASTM F963-11 (Section 8.12);16 CFR 1500.50, 1500.51d, 1500.52d, 1500.53d
ASTM F963-11 (Section 8.5);Use and Abuse Testing Normal Use Testing
ASTM F963-11 (Section 8.7);Impact / Drop Test
ASTM F963-11 (Section 8.8);Torque
ASTM F963-11 (Section 8.9);16 CFR 1500.50, 1500.51f, 1500.52f, 1500.53f
ASTM G110;IGA Preparation
ASTM G147;Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
ASTM G151;UV Exposure QUV Fluorescent Light Apparatus (General)
ASTM G151-10;Standard Practice for Exposing Nonmetallic Materials in Accelera ted Test Devices DID Use Laboratory Light Sources
ASTM G152;Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials Ford FLTM BO 101-01 Resistance to Artificial Weathering Fuji TS420-1-12 (2002) Honda HES D2500 (3.12.1) Light Resistance Test Hyuandai/KIA MS 260-13 , Section 4.8 (2005) Staining Resistance Test
ASTM G153;Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
ASTM G154;UV Exposure QUV Fluorescent Light Apparatus, Accelerated Weathering
ASTM G154-12a;Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials
ASTM G155;Weathering – Xenon Arc
ASTM G155-05a;Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
ASTM G195;Wear Testing by Taber Abrader Chamber Manual Environmental Simulation
ASTM G21;Determining Fungi Resistance To
ASTM G26-962 (Withdrawn 2000);Operating Light-Exposure Apparatus (Xenon-Arc)
ASTM G34;Exfoliation Corrosion
ASTM G48;Pitting / Crevice Corrosion Resistance
ASTM G85;Sulfur Dioxide/Salt Spray
ASTM G85-02 Annex A1;Acetic Acid-Salt Spray Test
ASTM G87;Sulfur Dioxide/Salt Spray Conducting Moist SO2 Tests
ASTM G91;Sulfur Dioxide/Salt Spray Monitoring Atmospheric SO2 Deposition Rate for Atmospheric Corrosivity Evaluation
Inspection & Approval Certificates : C/W Certificate (Calibration Works Certificate) EN 10204 3.1 / DIN 50049 3.1 / ISO 10474 3.1 Mill Test Certificate,
NACE HIC TM-0284 / NACE MR-0103 / NACE MR-0175 / ISO 15166, CE Marked, European Pressure Equipment Directive PED-2014/68/EU, AD-2000-WO,
ASME Boiler & Pressure Vessel Code Section-II Part A Edition 2019, API 6A (American Petroleum Institute), with 3.2 Certificate duly Certified &
Approved by IBR (Indian Boiler Regulations), LR Class (Lloyd’s Register), GL (Germanischer Lloyd), BV (Bureau Veritas), DNV (Det Norske Veritas),
ABS Class (American Bureau of Shipping), SGS, TUV, RINA, IR Class (Indian Register of Shipping), NORSOK Approved Standard M-630, M-650 Rev.3
If you have any requirement of above items, please feel free to contact us
Regards,
CONTACT PERSON :
MUKESH SHAH
Director
Mobile No. 0091 – 9820292499
Email – marketing@rolexmetals.com
ROLEX METAL DISTRIBUTORS
57-A Khatargalli
Thakurdwar
Mumbai – 400 002 India
0091-22-23858802
0091-22-23823963
0091-22-23898724
marketing@rolexmetals.com
www.rolexmetals.com
CHAIRMAN – chairman@rolexmetals.com
MANAGING DIRECTOR – managingdirector@rolexmetals.com
TECHNICAL DIRECTOR – technicaldirector@rolexmetals.com
SALES DIRECTOR – salesdirector@rolexmetals.com
COMMERCIAL DIRECTOR – commercialdirector@rolexmetals.com
COMMERCIAL MANAGER – commercial@rolexmetals.com
GENERAL MANAGER – generalmanager@rolexmetals.com
SALES MANAGER – salesmanager@rolexmetals.com
PURCHASE MANAGER – purchasemanager@rolexmetals.com
TECHNICAL MANAGER – technical@rolexmetals.com
WORKS MANAGER – worksmanager@rolexmetals.com
STORES MANAGER – stores@rolexmetals.com
WAREHOUSE MANAGER – warehouse@rolexmetals.com
SALES DOMESTIC – salesdomestic@rolexmetals.com
SALES INTERNATIONAL – salesinternational@rolexmetals.com
SALES GENERAL – sales@rolexmetals.com
PURCHASE GENERAL – purchase@rolexmetals.com
FINANCE MANAGER – finance@rolexmetals.com
ACCOUNTS MANAGER – accounts@rolexmetals.com
GENERAL INFORMATION – info@rolexmetals.com
EXPORT MANAGER – export@rolexmetals.com
IMPORT MANAGER – import@rolexmetals.com
AIR EXPORT – airexport@rolexmetals.com
SEA EXPORT – seaexport@rolexmetals.com
CUSTOMS – customs@rolexmetals.com
AIR FREIGHT – airfreight@rolexmetals.com
SEA FREIGHT – seafreight@rolexmetals.com
DESPATCH – despatch@rolexmetals.com
INSPECTION – inspection@rolexmetals.com
LOGISTICS – logistics@rolexmetals.com
TRANSPORT – transport@rolexmetals.com
KALAMBOLI WAREHOUSE – kalamboli@rolexmetals.com
TALOJA WAREHOUSE – taloja@rolexmetals.com
KHOPOLI WAREHOUSE – khopoli@rolexmetals.com
NHAVA SHEVA WAREHOUSE – nhavasheva@rolexmetals.com
KANDLA WAREHOUSE – kandla@rolexmetals.com
MUMBAI WAREHOUSE – mumbai@rolexmetals.com
STOCKYARD – stockyard@rolexmetals.com
SERVICE – service@rolexmetals.com
SUPPORT – support@rolexmetals.com
RECRUITMENT – career@rolexmetals.com
WEBMASTER – webmaster@rolexmetals.com
CUSTOMER CARE – customercare@rolexmetals.com